Seleziona il tipo di ricerca:

Torna alla pagina precedente TORNA CATALOGO / MODELLI DINAMICI / AEREI ELETTRICI/ALIANTI / .7 ALIANTI MOTORIZZATI / GRA9920-100

Articolo : GRA9920-100 Disponibilità :  Scarsa  PochiPz.
Prezzo : 159.90 €
Prezzo Web :    155.00 €
Quantità :
Il prodotto è stato inserito nel carrello!    


    HoTT FAN 1800RC E MOTO ALIANTE

    HoTT FAN 1800RC E MOTO ALIANTE   HoTT FAN 1800RC E MOTO ALIANTE   HoTT FAN 1800RC E MOTO ALIANTE
    HoTT FAN 1800RC E MOTO ALIANTE

    CON PINNA RETRATTILE

    Fornitore

    ARTF model
    Ready to fly in just a few minutes
    Attractive semi-scale design
    Full aerobatic capability
    Super flight performance with LiPo 3/1600
    Highly effective impeller folding engine
    Can take off from the ground on a smooth runway
    No gluing required
    Very small transport dimensions 95x21x19 cm

    The Graupner/SJ HoTT-FAN is a particularly attractive RC model. The HoTT-FAN is equipped with a highly efficient impeller folding engine. This engine provides the HoTT-FAN with very good climbing performance and generates a pleasing noise similar to a turbine. In this regard the model comes very close to its full-size version, the Super Salto by Bob Carlton. The original aircraft is powered by a PBS TJ-100 turbine. As with the full-size version, it can perform particularly impressive high-speed airfield fly-pasts at very low altitude. During landings, its incredibly good glide performance can be compensated by extending the engine, which then acts as an air brake.
    The ARTF model is almost ready to fly as soon as you take it out of the packaging. Simply push on the fixed-wing halves, screw on the V-tail and the model is assembled in all its glory. Once the HoTT receiver and the LiPo battery (not included) are connected, the model is then ready for take-off.

    Finished model made of Graupner SOLIDPOR® hard foam, separable air foil with CFRP strut. Finished fuselage with installed folding engine and removable canopy. BRUSHLESS motor HPD 2512-5000 7.4 V, includes BRUSHLESS CONTROL 22 and 58 mm impeller installed ready for operation. 4 x mini servos installed and ready for use, decals applied/painted. Detailed operating manual containing extensive tips for initial flights

    Barcode 4013389490016


    Aggiungi l'articolo alla lista dei desideri!
     Articolo aggiunto alla tua lista dei desideri! 
    HoTT FAN 1800RC E MOTO ALIANTE
    Caratteristiche :

    Scale 1:7,5
    Wingspan approx. 1800 mm
    All-up weight, approx. 850gr
    Total surface area 26,8 dm²
    Tailplane section NACA 008
    Wing section Eppler E-195
    Wing loading 31,7 g/dm²
    Tailplane area 4,2 dm²
    Overall length, approx. 810 mm
    Wing area 22,6 dm²

    Accessori necessari non inclusi :
    - LiPo 11,1v 1600mAh con cavetto G3.5


    Aggiungi l'articolo alla lista dei desideri!
     Articolo aggiunto alla tua lista dei desideri! 
    HoTT FAN 1800RC E MOTO ALIANTE

    CON PINNA RETRATTILE

    Fornitore

    ARTF model
    Ready to fly in just a few minutes
    Attractive semi-scale design
    Full aerobatic capability
    Super flight performance with LiPo 3/1600
    Highly effective impeller folding engine
    Can take off from the ground on a smooth runway
    No gluing required
    Very small transport dimensions 95x21x19 cm

    The Graupner/SJ HoTT-FAN is a particularly attractive RC model. The HoTT-FAN is equipped with a highly efficient impeller folding engine. This engine provides the HoTT-FAN with very good climbing performance and generates a pleasing noise similar to a turbine. In this regard the model comes very close to its full-size version, the Super Salto by Bob Carlton. The original aircraft is powered by a PBS TJ-100 turbine. As with the full-size version, it can perform particularly impressive high-speed airfield fly-pasts at very low altitude. During landings, its incredibly good glide performance can be compensated by extending the engine, which then acts as an air brake.
    The ARTF model is almost ready to fly as soon as you take it out of the packaging. Simply push on the fixed-wing halves, screw on the V-tail and the model is assembled in all its glory. Once the HoTT receiver and the LiPo battery (not included) are connected, the model is then ready for take-off.

    Finished model made of Graupner SOLIDPOR® hard foam, separable air foil with CFRP strut. Finished fuselage with installed folding engine and removable canopy. BRUSHLESS motor HPD 2512-5000 7.4 V, includes BRUSHLESS CONTROL 22 and 58 mm impeller installed ready for operation. 4 x mini servos installed and ready for use, decals applied/painted. Detailed operating manual containing extensive tips for initial flights

    Barcode 4013389490016


    Aggiungi l'articolo alla lista dei desideri!
     Articolo aggiunto alla tua lista dei desideri! 
I prezzi scontati sono validi solo per prenotazioni o acquisti On-Line

Note tecniche e descrizioni dei vari articoli sono pubblicati così come vengono forniti dal costruttore e/o distributore, immagini allegate comprese, e potrebbero contenere delle inesattezze o delle omissioni. Non ci assumiamo quindi alcuna responsabilità a riguardo.


Modellismo Gianni - Via Pier Vittorio Aldini n.41   Roma (Uscita G.R.A. Ciampino Zona Industriale)
Tel. 06/72673332 • Fax. 06/72677092 • P. IVA 04563861006 • Mail: info@modellismogianni.it © Modellismo Gianni 2007
NOTA: tutti i prodotti da Noi distribuiti recepiscono la DIRETTIVA R.&.T.T.E. 1999/5/CE DECRETO LEGISLATIVO 269/01
PAGAMENTI :     CONSEGNE IN 24/48 ORE :

 webmaster : Massimo Marra